Since 1 January, 2008,

  paws have visited us.

For our doghouse, we used scraps of vinyl siding to match the house.

Home improvement may extend beyond your house to that of your pet. The family dog needs a good place to escape from the weather, and unless you're willing to let him in the house, maybe its time to work on that doghouse you've been meaning to build. Building a doghouse is a great family project. With these instructions a beginner level DIYer should be able to complete this project in a weekend, using common household tools. Lowe's is happy to provide this information as a service to you.

Tools (typical)	Materials (typical)
Safety glasses Tape measure Hammer Square  Circular saw Table saw (optional) Paintbrush	4'x8' sheet of 5/8" exterior siding 1— 8' 2x4 (to be cut into 2x2's) 1— 10' 2x4, rated for outdoor use Nails—16d for base, 8d for house, and short roofing nails if using shingles Shingles (optional) Finishing material (paint or nontoxic wood preservative)

Overview

SAFETY NOTE: Make sure nails are accurately driven. You don't want the points of nails sticking into the living space of your pet; they could cause injury.

Building an attractive and safe doghouse doesn't have to be a complicated project. Just keep a few basic principles in mind:

• The house should have a floor which sits far enough above ground to prevent water from entering on the rainiest days. Raising the floor will also isolate it from the cold ground in the winter.

• Consider your dog's habits. For example, some dogs like to sit on top of their house. If you suspect that this may be the case with your dog, don't put any roll roofing or shingles on the top of the house since they can get hot in the summer sun. Just use an exterior plywood panel, treated with a nontoxic preservative like linseed oil. (The doghouse in this how-to uses a traditional peaked roof design, but could easily be modified to incorporate a slanted roof.)
• The illustrated doghouse was designed for an average sized dog. Feel free to scale the dimensions up or down as necessary to accommodate your dog. It should be large enough to allow your pet to turn around easily in it. Don't make it too large, since a smaller house is more easily heated by the dog's natural body heat—an important consideration in winter.
  

Cutting Out the Parts

The illustration at left provides the dimensions for the panel elements of our doghouse. The house is designed to make the most use of a single sheet of plywood siding. Notice that the drawing has two floor panels—this is so you can double the thickness of the floor for rigidity.

Step 1: Lay out the panels on the back of the siding as shown in the drawing. Then, carefully cut out the panels on the lines. Cut the entry hole only large enough to allow your dog easy access.

Step 2: Cut your 10' 2x4 into the following:

• 2 pieces 22-7/8" long (platform sides)
  
  
• 2 pieces 20 3/4" long (platform front and back)
  
  
• 4 pieces 6" long (platform legs)

These will be used to build the platform on which the house will be built.

Assembling the Platform

Consult the drawing at right when performing the following steps:

Step 1: Round the bottom of the 6" platform legs.

Step 2: With tops aligned, nail the legs flush against the inside edges of the 22-7/8" long side pieces of the platform.

Step 3: Assemble the frame by nailing the 20 3/4" front, back and side pieces in place as shown.

Note: The front and back pieces overlap the ends of the side pieces.

Step 4: Finally, align the first floor panel with the frame. It should align without overhanging edges. This will assure that the frame is square and that it was properly assembled. If the floor and frame don't match up, double-check to make sure you have correctly assembled the frame. If the frame is assembled properly but there is a slight overhang in a place or two (perhaps because the panels weren't cut perfectly straight), trim off the excess with a plane or circular saw. When all is well, nail both floor panels in place.

Building the House

Step 1: Rip the 8' 2x4 into 2x2 stock to be used as frame elements.

Step 2: From these, cut 4 pieces 12 1/2" long.

Step 3: Nail these pieces flush against the short edges of the sides. One frame piece should be positioned starting at the top of each side corner, leaving a 3 1/2" space at the bottom to allow the side panel to overhang the platform.

Also attach frame pieces to the inside roof line of the front and back panels. The frame pieces should meet at the top, and extend along the roof line to approximately 2 1/2" from the sides.

Step 4: Put one of the sides in place (the edges of the side should align with the front and back of the platform) and nail it to the platform at the bottom. Repeat this step for the other side.

Step 5: Now you may attach the back of the doghouse. Align it with the sides, and nail it in place, first against the platform, then into the 2"x 2" frame members in the corners. Do the same for the front.

You now have a doghouse with no roof. While you still have the chance, check carefully inside the house to make sure there are no exposed nail points. Cut and file down the edges of any exposed nails that could injure the dog.

Putting on the Roof

Step 1: Nail a 22" long piece of 2"x 2" flush against the top inside edge of one of the roof panels (along the 32" axis). The piece should be centered, 5" in from the edges of the panel. When both roof panels are installed, this piece will run across and support the ridge cap.

Step 2: Place the first roof panel in position (the one with the frame piece along the top inside edge), and nail it to the frame attached to the top of the front and back of the doghouse. Be careful not to miss with the nails. You don't want to leave exposed nail points inside the doghouse. You may not be able to get inside once it is finished to take care of any problems!

Finishing the Doghouse

Shingles are an inexpensive and attractive way to prevent a doghouse from leaking. If you wish, you can shingle the dog's house to match your own. They are not hard to install, and a doghouse—unlike your own home—is forgiving of mistakes.

For a doghouse, using roofing felt is optional. If you have some lying around, or if you are just super conscientious and really really love your dog, staple the paper to the roof in a single sheet running up one side and down the other. Be stingy with those staples though; you just need to hold the stuff in place until you can install the shingles.

Run the first row of shingles upside down (split tabs up) along the bottom of the roof edges. Use short roofing nails. Then, starting directly on top of this row, begin nailing the shingles in place in the pattern you desire. Cap the ridge with cut shingle tabs to prevent leaking. Take a look at your own roof. . .it will show you how it should look.

If you choose not to use shingles, form a cap from a piece of aluminum flashing to run along the joint where the two roof panels meet. Run two beads of roofing cement, or silicone caulk, along the bottom of the cap and nail it in place.

Round and sand any rough edges of the doghouse which could injure your dog. Some people prime and paint their doghouses to match their homes. Others treat the wood with linseed oil only. . .in case the dog tries to eat it. If you do paint your doghouse, use a good quality exterior latex house paint.

Was this information helpful? Please let us know your do-it-yourself experiences. We'd love to hear from you!

These How-To's are provided as a service from Lowe's, the Original Home Improvement Warehouse of How-To Information for the World Wide Web. The information in Lowe's "How-To" clinics is intended to simplify jobs around the house. Tools, products, materials, techniques, building codes and local regulations change; therefore, Lowe's assumes no liability for omissions, errors or the outcome of any project. The reader must always exercise reasonable caution, follow applicable codes and regulations, and is urged to consult with a professional if in doubt about any procedures. Please read our terms of use.

© 1997 Lowe's Home Centers, Inc. All rights reserved.

Stats

Send mail to Don Kemp with questions about membership, Janet Danner for breed referral and information and brett@tidewaterkc.org with questions or comments about this web site.
Copyright © 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010 Tidewater Kennel Club
Last modified: 03/26/2010